一本色综合久久-一本色综合网久久-一本色综合亚洲精品蜜桃冫-一本无码人妻在中文字幕免费-一本无码中文字幕在线观-一本一本久久aa综合精品

Welcome to the official website of Legret Metal Company
Focus on electronic welding for 20 yearsDONGGUAN LEGRET METAL.,LTD
National consultation hotline:135-2799-2739
Contact US
mobile phone: 135-2799-2739
Service hotline: 0769-38893080
Email: lzd@dglzd.com
Address: Dongguan lvzhidao Metal Co., Ltd
Contact person: Manager Zeng
Industry information

What should be paid attention to when using reflow solder paste? In the process of reflow soldering, what kind of change will happen?

作者:Lvzhidao solder factory 2021-03-02 0

What should be paid attention to when using reflow soldering? In the process of reflow soldering, what kind of change will happen?


1、 When the solder paste reaches the heating zone, the temperature begins to rise. The temperature rise must be slow (about 2 ℃ ~ 3 ℃ per second) to prevent boiling and splashing and to avoid the formation of small solder beads; Some components are sensitive to internal stress, which may cause fracture when the external temperature of components rises too fast( At this time, the solvent used to improve the screen printing performance and viscosity of solder paste begins to evaporate.)


2、 The flux inside the solder paste starts to be active, and the chemical cleaning action begins. The same cleaning action will take place for both water-soluble flux and free cleaning flux, but the temperature required to start the action is slightly different( At this time, the chemical cleaning action will remove the metal oxide and some contamination from the solder particles and metal to ensure that the metallurgical requirements of the "clean" solder joint surface are met


3、 When the temperature in reflow soldering furnace continues to rise, a single solder particle begins to melt, liquefy and absorb tin on the surface. In this way, all the surfaces that may be covered begin to cover and solder spots gradually form.


4、 This stage is the most important in reflow soldering. When all the individual solder particles are melted and combined with the liquid tin formed due to high temperature, the surface of solder pin begins to form under the action of surface tension. If the gap between component pin and PCB pad exceeds 0.1mm, the pin and pad may be separated under the action of surface tension, As a result, the solder joint is open.


5、 When the solder joint formed by solder paste enters the cooling zone, the solder joint begins to cool. If the cooling speed is a little faster, the strength of the solder joint will increase, but it should not be cooled too fast, otherwise it will cause the internal temperature stress of the component.




主站蜘蛛池模板: 日韩国产午夜一区二区三区 | 亚洲精品一区二区三区婷婷 | 草久久久| 欧美色交| 2021在线永久免费视频 | 欧美日韩中文字幕在线观看 | 色综合在 | 亚洲专区一路线二 | 日韩不卡一区二区三区 | 末成年一级在线看片 | 国产在线操 | 99中文字幕在线 | 国产精品亚洲第五区在线 | 国产欧美日韩精品一区二 | 国产永久视频 | 久久久久久久91精品免费观看 | 亚洲国产日产韩国欧美综合 | 亚洲精品乱码久久久久 | 亚洲欧美日韩另类 | 日韩城人视频 | 欧美日韩亚洲一区二区 | 在线观看麻豆精品国产不卡 | 久久国产精品高清一区二区三区 | 亚洲综合网址 | 国产精品视频久久 | 99久久精品无码一区二区毛片 | 午夜精品在线视频 | 夜夜爱夜夜爽夜夜做夜夜欢 | 狼狼色丁香久久婷婷综合五月 | 高清国产精品久久久久 | 久久久久在线 | 国产精品久久久久久久网站 | 欧美精品亚洲人成在线观看 | 色噜噜视频 | 欧美日韩北条麻妃一区二区 | 天天射网站 | 99精品久久99久久久久久 | 香蕉视频网站入口 | 国产欧美一区二区三区久久 | 99er热久久精品中文字幕 | 四虎影视com88 |